FRM220-CCF40 & FRM220-CCF20
Contact Closure Fiber Converter with In-Band Management
FRM220-CCF40 & FRM220-CCF20
4ch / 2ch Contact Closure Fiber Converter Card
The FRM220-CCF contact closure fiber converter comes in two models, one with 2 channels (CCF20) and one with 4 channels (CCF40) and provides the transmission of contact closure over a single fiber optic link. With SFP cage on fiber ports, the FRM220-CCF gives you the fiber cabling connector SFP-LC, both multi-mode and single-mode, as well as BiDi which allows bi-directional transmission using only a single fiber core. The FRM220-CCF has contact inputs and 0.5 amp contact output relays. The relay output follows the “relay input” from the remote end. When the remote “relay input” is shorted, the local relay output is closed and vice-versa. Any one of the relay outputs can be configured to close when “carrier loss” is detected from the remote end. (Either through a CH01M console or via NMC in managed chassis.) Carrier Loss indicates that the optical fiber is disconnected or that the remote end has lost power and is not operating. This "carrier loss" relay can then be connected to an appropriate alarm circuit.
Contact Closure Fiber Converter with In-Band Management
FRM220-CCF40 & FRM220-CCF20
4ch / 2ch Contact Closure Fiber Converter Card
The FRM220-CCF contact closure fiber converter comes in two models, one with 2 channels (CCF20) and one with 4 channels (CCF40) and provides the transmission of contact closure over a single fiber optic link. With SFP cage on fiber ports, the FRM220-CCF gives you the fiber cabling connector SFP-LC, both multi-mode and single-mode, as well as BiDi which allows bi-directional transmission using only a single fiber core. The FRM220-CCF has contact inputs and 0.5 amp contact output relays. The relay output follows the “relay input” from the remote end. When the remote “relay input” is shorted, the local relay output is closed and vice-versa. Any one of the relay outputs can be configured to close when “carrier loss” is detected from the remote end. (Either through a CH01M console or via NMC in managed chassis.) Carrier Loss indicates that the optical fiber is disconnected or that the remote end has lost power and is not operating. This "carrier loss" relay can then be connected to an appropriate alarm circuit.
Contact Closure Fiber Converter with In-Band Management
FRM220-CCF40 & FRM220-CCF20
4ch / 2ch Contact Closure Fiber Converter Card
The FRM220-CCF contact closure fiber converter comes in two models, one with 2 channels (CCF20) and one with 4 channels (CCF40) and provides the transmission of contact closure over a single fiber optic link. With SFP cage on fiber ports, the FRM220-CCF gives you the fiber cabling connector SFP-LC, both multi-mode and single-mode, as well as BiDi which allows bi-directional transmission using only a single fiber core. The FRM220-CCF has contact inputs and 0.5 amp contact output relays. The relay output follows the “relay input” from the remote end. When the remote “relay input” is shorted, the local relay output is closed and vice-versa. Any one of the relay outputs can be configured to close when “carrier loss” is detected from the remote end. (Either through a CH01M console or via NMC in managed chassis.) Carrier Loss indicates that the optical fiber is disconnected or that the remote end has lost power and is not operating. This "carrier loss" relay can then be connected to an appropriate alarm circuit.
Features
Transmits a single contact closure in one or two directions
Distances up to 120km
30 VDC, 0.5 amp relay N.O. (Normally Open)
Point-to-Point transmission architecture
Plug-and-play design ensures ease of installation requiring no electrical or optical adjustments
Relay contact for Carrier Detect, N.C. (Normally Close)
Indicating LEDs are provided for confirming equipment operating status
Managed when places in FRM220 chassis with NMC